Vakbarát változat




 

Ласкаво просимо на наш сайт
і ми хотіли б звернути вашу увагу на деякі з наших продуктів, в даний час тільки на англійській мові.

 
 

Commercial Pit Jack

(hydro pneumatic, electro hydraulic and hand oprerated)

Hydro pneumatic pit jack for lifting up commercial vehicles, agricultural machinery and other special vehicles over pits. The carriage construction is fitted to the width of the pit /any specifications should be defined at ordering on a separate data sheet / from 790 to 1100 mm, to be adjusted accurately and fixed with bolts and nuts. Four so-called bogie wheels allow the carriage to be rolled manually. The cross-axle carriage containing a hydraulic unit is also rolling on wheels thus it can be easily pulled to the proper position.

 

 

The hydraulic mechanism is operated by a two-way valve via the air tube, with a quick-positioning function to one direction, and with a load lifting function to the other. When pressed, oil is pumped under the ram, which starts to lift. It can be lowered with the handle in the middle of the hydraulic hoist; by pressing down the handle the ram starts to lower slowly and sets back to the initial position.

Technical specifications

DA-200/8L   capacity    8 tons,stroke: 720 mm dead load appr. 130 kg

DA-200/10L capacity: 10 tons stroke: 720 mm dead load appr. 145 kg

DA-200/12L capacity: 12 tons stroke: 720 mm dead load appr. 150 kg

DA-200/13L capacity: 13 tons stroke: 720 mm dead load appr. 150 kg

DA-200/15L capacity: 15 tons stroke: 720 mm dead load appr: 170 kg

DA-200/20L capacity: 20 tons stroke: 720 mm dead load appr. 180 kg

An additional assistant hoist can also be used with the mechanism, whose capacity is 8-10-12-13-15-20 tons. Operation: it can be linked to the hydraulic ram, into which a hoist.


Electro-hydraulic pit jack for lifting up commercial vehicles, agricultural machinery and other special vehicles over pits. The carriage construction is fitted to the width of the pit /any specifications should be defined at ordering on a separate data sheet / from 790 to 1100 mm, to be adjusted accurately and fixed with bolts and nuts. Four so-called bogie wheels allow the carriage to be rolled manually. The cross-axle carriage containing a hydraulic unit is also rolling on wheels thus it can be easily pulled to the proper position.

 

The hydraulic mechanism is operated  by a gear pump. When pressed, oil is pumped under the ram, which starts to lift. It can be lowered with the handle in the middle of the hydraulic hoist; by pressing down the handle the ram starts to lower slowly and sets back to the initial position.

Technical specifications:

DA-200/8E   capacity    8 tons,stroke: 720 mm dead load appr. 130 kg

DA-200/10E capacity: 10 tons stroke: 720 mm dead load appr. 145 kg

DA-200/12E capacity: 12 tons stroke: 720 mm dead load appr. 150 kg

DA-200/13E capacity: 13 tons stroke: 720 mm dead load appr. 150 kg

DA-200/15E capacity: 15 tons stroke: 720 mm dead load appr: 170 kg

DA-200/18E capacity: 18 tons stroke: 720 mm dead load appr. 180 kg

An additional assistant hoist can also be used with the mechanism, whose capacity is 8-10-12-13-15- 18 tons. Operation: it can be linked to the hydraulic ram, into which a hoist.


Hand operated hydraulic pit jack for lifting up commercial vehicles, agricultural machinery and other special vehicles over pits. The carriage construction is fitted to the width of the pit /any specifications should be defined at ordering on a separate data sheet / from 790 to 1100 mm, to be adjusted accurately and fixed with bolts and nuts. Four so-called bogie wheels allow the carriage to be rolled manually. The cross-axle carriage containing a hydraulic unit is also rolling on wheels thus it can be easily pulled to the proper position

 

The hydraulic mechanism is operated by a two speed manual pump, a quick-positioning function, and a load lifting function. When pressed  oil is pumped under the ram, which starts to lift. It can be lowered with the handle in the middle of the hydraulic hoist; by pressing down the handle the ram starts to lower slowly and sets back to the initial position. 

Technical specifications:

DA-200/8K   capacity    8 tons,stroke: 720 mm dead load app. 130 kg

DA-200/10L capacity: 10 tons stroke: 720 mm dead load appr. 145 kg

DA-200/12K capacity: 12 tons stroke: 720 mm dead load appr. 150 kg

DA-200/13K capacity: 13 tons stroke: 720 mm dead load appr. 150 kg

DA-200/15K capacity: 15 tons stroke: 720 mm dead load appr: 170 kg

DA-200/20K capacity: 20 tons stroke: 720 mm dead load appr. 180 kg 

An additional assistant hoist can also be used with the mechanism, whose capacity is 8-10-12-13-15-20 tons. Operation: it can be linked to the hydraulic ram, into which a hoist.



Pit type lift

(for cars and light commercial vehicles)

Hydro pneumatic pit jack for lifting up cars and light trucks over pits. The carriage construction is fitted to the width of the pit /any specifications should be defined at ordering on a separate data sheet / from 750 to 1100 mm, to be adjusted accurately and fixed with bolts and nuts. Four so-called bogie wheels allow the carriage to be rolled manually. The cross-axle carriage containing a hydraulic unit is also rolling on wheels thus it can be easily pulled to the proper position.

The hydraulic mechanism is operated by an air motor via the air tube, for load lifting function. When pressed, oil is pumped under the ram, which starts to lift. It can be lowered with the handle in the middle of the hydraulic hoist; fotate the handle the ram starts to lower slowly and sets back to the initial position.

Technical datas:

Type:

DA-200/2L

DA-200/4L

DA-200/7L

Loding capacity:

2 to

4 to

7 to

Hidraulic lifting.:

485 mm

485 mm

485 mm

Lifting time:

30 s

30 s

30 s

Lowering time:

12 s

12 s

12 s

Net weight:

kb. 75 kg

kb. 78 kg

kb. 90 kg

Air comsuption:

min. 6 bar

min. 6 bar

min. 6 bar

Included:

1 pc complete plate with rubber cover


 

Manual operated hydraulic pit jack for lifting up cars and light commercial vehicles over pits. The carriage construction is fitted to the width of the pit /any specifications should be defined at ordering on a separate data sheet / from 790 to 1100 mm, to be adjusted accurately and fixed with bolts and nuts. Four so-called bogie wheels allow the carriage to be rolled manually. The cross-axle carriage containing a hydraulic unit is also rolling on wheels thus it can be easily pulled to the proper position.

The hydraulic unit can be manually operated, for load lifting function. 
When pressed oil is pumped under the ram, which starts to lift. It can be lowered with the handle in the middle of the hydraulic hoist; 
turning the handle the ram starts to lower slowly and sets back to the initial position.

Technical datas:

Type:

DA-200/2K

DA-200/4K

DA-200/7K

Loding capacity:

2 to

4 to

7 to

Hidraulic lifting.:

485 mm

485 mm

485 mm

Lifting time:

30 s

30 s

30 s

Lowering time:

12 s

12 s

12 s

Net weight:

kb. 70 kg

kb. 72 kg

kb. 85 kg

Air comsuption:

min. 6 bar

min. 6 bar

min. 6 bar

Included:

1 pc complete plate with rubber cover



 

Pit jack

 Jacking beams – Wheel-Free jack

Manual safety lock, lifting capacity 2 tons - 2,5 tons – 3 tons, min. height 226 mm, max. height 643 mm, width 820-1100 mm, length 434 mm, distance between arms 766-1626 mm, arm height 20-62 mm

Description

Can be operated with a hydraulic hand pump and a hydraulic air pump (pedal) (not accessories)

Lifting capacity

2-2,5-3-4 tons

Min. height

226mm

Max. height

643mm

Jack width

830-1000mm  

Jack length

434mm

Lifting table width

850mm

Lifting table length

330mm

Distance between arms  

766-1626mm

Arm height

20-62mm

 


 

Support system

For permanent lifting and long-term mounting a support system should be used.

Lift the truck with the pit type lift and place it on the support system.

The pit type lift can be rolled out and use it for other elevations.

Support system size:

 Adjusting to the size of the mounting shaft, but can also be located at ground level, and 

can be placed in the "U" profile. The U profile has a minimum size of 220 mm.

 

the support can be adjusted and used only in pairs 

Technical datas  

DA-200/3S                           3 tons,                    adjustability           92-432 mm 

DA-200/6S                            6 tons                    adjustability          390-618 mm 

DA-200/12S                         12 tonna                adjustability           445-700 mm 

DA-200/18S                         18 tons                   adjustability           445-700 mm



 

Grearbox supporting and delivering

 

It is an adapter for the main pieces of vehicles are primarily gearboxes to lift and transport, universal design. The connector and clamping elements can be adjusted to the gearbox dimensions, not only adjustable but also tiltable . The adapter can be connected to the piston bore.

It has a load capacity of 0.6 kN but it is also possible to order another version.

 

 

 

Two point lifting beam


 

for cars and light commercial vehicles 

adjustable from 560 – to 850 mm

 

 

for commercial and heavy vehicles

 adjustable from 0 – to 800 mm 

 Technical datas:

 its load capacity fits the hoist, which is from 2 to 20 tons




 

Play detectors

 DH-12000H4 /DH15000H4/DH18000H4/DH-20000H4

 

The DH type is a hydraulic wheel play detector for light and heavy vehicles, busses and coaches up to 20.000 kg axle load. It consist of two strong steel plates - one for each wheel - which are installed into the floor. The plates are moved horizontally in 8 different directions by means of a remote control. The remote control features both an integrated flash light functionality and a keypad to control each movement of the plates. The operator can choose to control each movement manually.

The power unit is installed in the pit either at the end or inside an excess in the wall of the inspection pit. The DH play detector checks the steering and suspension system of the vehicle without need of jacking up the axle. The operator will be able to detect worn kingpin bushings, loose tie-rod ends, broken welds, loose fasteners and other failed components.

 

 

 

Play detectors

 DH-2000H4 /DH-4000H4

 

The DH type is a hydraulic wheel play detector for car and light vehicles, up to 4.000 kg axle load. It consist of two strong steel plates - one for each wheel - which are installed into the floor. The plates are moved horizontally in 8 different directions by means of a remote control. The remote control features both an integrated flash light functionality and a keypad to control each movement of the plates. The operator can choose to control each movement manually.

 

The power unit is installed in the pit either at the end or inside an excess in the wall of the inspection pit. The DH play detector checks the steering and suspension system of the vehicle without need of jacking up the axle. The operator will be able to detect, loose tie-rod ends, broken welds, loose fasteners and other failed components.


 
 
Látogatók: 121.974   Oldalletöltések: 398.675   By NetOffice & Compagnon     w3c_html40 w3c_css20